Behringer Mini FBQ FBQ800 Compact 9-Band Graphic Equalizer with Feedback Detection System, 2 Channel, 10Hz-200kHz System Frequency response

SKU
BEH_FBQ800
Special Price $69.99 Regular Price $104.99
Available to Buy

$0.00 Tax Outside NY and NJ 

+1 (888) 606-6268

Click Here to request quote for bulk quantity

About Behringer FBQ800

The Behringer Mini FBQ FBQ800 Compact 9-Band Graphic Equalizer is an ultra-compact, nine-band graphic equalizer that also contains a feedback detection system that instantly reveals critical frequencies and that can also be used as an audio analyzer. An additional low cut filter removes unwanted frequencies such as floor rumble. An accurate six-digit LED input/output meters and level control are provided for precise level indication. Long-term reliability is assured with high-quality illuminated faders, potentiometer and illuminated switches.

Ultra low-noise audio operational amplifiers offer outstanding sound performance. In addition, all Mini Series models can be stacked on top of each other to create an ultra-compact signal processing solution.

FBQ800 Graphic Equalizer Working Process
Imagine the frequency range of the sound you hear as a highway, a very wide one with nine lanes. Each of these "lanes" represents a single octave of the sonic spectrum. The first four lanes, labeled 63 - 500 (Hz) contain the really low frequency sound content, mainly bass, bass vocals and the kick and tom drums. The three lanes labeled 1 k, 2 k and 4 k (Hz), make up the fundamental zone of most musical instruments and the male and female vocals. 8 k and 16 k cover the frequency range of cymbals, snare drums and higher pitched percussion instruments. The FBQ800 allows you to control the flow of audio traffic in each of these nine lanes. When properly applied, EQ makes it possible to hear all of these frequency ranges equally, thus the term equalization.

Feedback Elimination
When a specific frequency or range of frequencies, reaches too high a level, feedback occurs that all-too-familiar squeal or howl you get when the mic is too close to the speaker. Basically, feedback happens when there is so much of a particular frequency that it is picked up by the mic and run through the system again. That's why feedback typically gets louder and louder the longer it's allowed to occur. Needless to say, this kind of feedback is very undesirable. This is where the FBQ800's Feedback Detection System really works its magic. In this ingenious circuitry, LEDs on the individual faders light up when that frequency band is approaching the danger zone.

Sonic Toolkit
That really is the best way to describe the FBQ800. With its nine frequency bands, you easily fine-tune your sound and instantly eliminate feedback. And each fader can be used to boost or cut the frequency range it controls by as much as 12 dB. Special attention is paid to the low frequency zone. In addition to low frequency faders, the FBQ800 features a Low Cut filter for removing unwanted low frequencies such as floor rumble, room resonance, electrical hum, etc. This is especially handy if your system is being used for speech rather than music.

To Boost or to Cut
Raising and lowering specific frequency bands can improve the frequency response of any room's acoustics. For instance, if the room you're in is "bass-heavy," lowering the 63 and 125 Hz faders can help eliminate an overall "boomy" or "muddy" sound. Likewise, gently boosting the 8 and 16 k sliders can add sparkle to a somewhat "dark" mix. Are the vocals getting lost in the mix? Raising the level of the 1 k slider can help bring them out. It's important to note that raising a single fader level is not always the best solution; it's often better to lower the bands surrounding the frequency you want to bring out and then boost the overall volume level to achieve better headroom.

Built for Accuracy and Reliability
Speaking of headroom, FBQ800's 6-digit LED I/O meters and level control are provided for precise level maintenance. Long-term reliability is ensured, thanks to high-quality illuminated faders and switches and ultra low-noise audio operational amplifiers provide outstanding sonic performance. In addition, all Mini Series components can be stacked to create an ultra-compact signal processing solution.

More Information
Stock Status Available to Buy
Manufacturer Behringer
Mfr Part No FBQ800
Upc Number 689076750776
EAN Number 4033653010993
Condition New
Refundable / Cancelable? Yes
Specification
Signal-to-noise ratio
10 Hz - 22 kHz < 95 dB at 0 dBu, a-weighted
Input CMRR
40 dB typ. at 1 kHz
Input Type
1/4" TRS connectors (balanced) or RCA connectors (unbalanced)
Output Impedance
120 Ohms
Distortion
0.003% typ. at 0 dBu
Weight
0.86lbs (0.39kg)
Graphic Equalizer Control range
+/-6 dB or +/-12 dB, switchable
Graphic Equalizer Bandwidth
1 oct.
Frequency response
10 Hz to 200 kHz, -3 dB
Low-cut filter
75 Hz (12 dB/oct.)
Dimensions (H x W x D)
48 x 243 x 120mm (1.88 x 9.56 x 4.72")
Max. Output level
+15 dBu
Crosstalk
< 80 dBu at 1 kHz
Graphic Equalizer Type
9 analog stereo bands
Mains connection
external power supply, 9 V- / 750 mA
Input Impedance
20 kOhms, balanced
10 kOhms unbalanced
Output Type
1/4" TS connectors (unbalanced) or RCA connectors (unbalanced)
Max. Input Level
+15 dBu
Dynamic range
110 dB, 10 Hz to 22 kHz
Input level control
-12 dB to +12 dB
Mains Voltage
120 V-, 60 Hz
Write Your Own Review
You're reviewing:Behringer Mini FBQ FBQ800 Compact 9-Band Graphic Equalizer with Feedback Detection System, 2 Channel, 10Hz-200kHz System Frequency response
Your Rating